Individual Article

• After removing the hold-down clips, you might find that a landingear leg is stuck in the mounting block, and it’s difficult to pull straight out without bending it. Make a loop of strong fishing line, then slide it along under the horizontal torsion-bar part of the gear (as shown) until it reaches the vertical, embedded […]

  

  Removing Stuck Gear Legs

  After removing the hold-down clips, you might find that a landingear leg is stuck in the mounting block, and it’s difficult to pull straight out without bending it. Make a loop of strong fishing line, then slide it along under the horizontal torsion-bar part of the gear (as shown) until it reaches the vertical, embedded […]
  $1.99 $1.99 - Add to cart

• Hermeus was founded in 2018, the company notes, to transform the global transportation network. “Using lessons learned from our time at NewSpace companies, we’re developing Mach 5 aircraft to connect people faster and bring much needed innovation to commercial flight. This means planes flying five times faster than they do today. Mach 5 airplanes have […]

  

  Hermeus Supersonic Airliner

  Hermeus was founded in 2018, the company notes, to transform the global transportation network. “Using lessons learned from our time at NewSpace companies, we’re developing Mach 5 aircraft to connect people faster and bring much needed innovation to commercial flight. This means planes flying five times faster than they do today. Mach 5 airplanes have […]
  $1.99 $1.99 - Add to cart

• This is how it was done before there were nylon clevises. It’s an oldie, but goodie! The latch is made of 20-gauge music wire that has been bound and soldered. This is very useful in confined spaces, and it will never foul the servo-arm center at extremes of deflection. Adapted from 400 Great R/C Modeling […]

  

  Quick Release Pushrod End

  This is how it was done before there were nylon clevises. It’s an oldie, but goodie! The latch is made of 20-gauge music wire that has been bound and soldered. This is very useful in confined spaces, and it will never foul the servo-arm center at extremes of deflection. Adapted from 400 Great R/C Modeling […]
  $1.99 $1.99 - Add to cart

• Aviation Week recently reported on a few interesting new Russian aircraft designs that were revealed at the MAKS 2021 air show. Among these was the metallic gray Yak-40LL with an extended nose. “The experimental Yak-40LL aircraft with a hybrid power plant flew at MAKS 2021 for the first time on July 24. The Yak-40LL has […]

  

  Russian Experimental Aircraft Designs shown at MAKS 2021

  Aviation Week recently reported on a few interesting new Russian aircraft designs that were revealed at the MAKS 2021 air show. Among these was the metallic gray Yak-40LL with an extended nose. “The experimental Yak-40LL aircraft with a hybrid power plant flew at MAKS 2021 for the first time on July 24. The Yak-40LL has […]
  $1.99 $1.99 - Add to cart

• Graham Warwick reported in the 16 August Aviation Week magazine that DARPA is exploring the concept of an “X Prime” program that would fit between an experimental X-plane and a Y-plane prototype and help move a prototype forward from research to operation. One of DARPA’s current projects is the “Shepard” program (for Series Hybrid-Electric Propulsion […]

  

  DARPA X Prime Program Contemplates Hybrid Electric Flying Wing

  Graham Warwick reported in the 16 August Aviation Week magazine that DARPA is exploring the concept of an “X Prime” program that would fit between an experimental X-plane and a Y-plane prototype and help move a prototype forward from research to operation. One of DARPA’s current projects is the “Shepard” program (for Series Hybrid-Electric Propulsion […]
  $1.99 $1.99 - Add to cart

• If you have trouble getting you servo mounts parallel and level, try this. Sandwich the fuselage sides together, determine the servo location from the plan, then drill holes to accept ¼-inch or 5/16-inch dowels. After the fuselage has been assembled and squared up, push the dowels through and glue them as shown. You should also […]

  

  Parallel Servo Mounts

  If you have trouble getting you servo mounts parallel and level, try this. Sandwich the fuselage sides together, determine the servo location from the plan, then drill holes to accept ¼-inch or 5/16-inch dowels. After the fuselage has been assembled and squared up, push the dowels through and glue them as shown. You should also […]
  $1.99 $1.99 - Add to cart